LinuxTarget system not able to discover Delphix Engine

  • 0
  • 1
  • Problem
  • Updated 3 years ago
  • Solved
I have installed successfully Delphix engine and source. But the target system is not able to identify the Delphix engine. Every 60 seconds it is trying to poll to identify the engine. Could you please advice how to resolve this issue.
Photo of saran

saran

  • 140 Points 100 badge 2x thumb

Posted 3 years ago

  • 0
  • 1
Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
Sure. Can you please post the output of the following command as the delphix user on the linuxtarget?

tail -20 landshark_setup.log
Photo of saran

saran

  • 140 Points 100 badge 2x thumb

Please find the below log

Repeating discovery loop in 60 seconds.
Ensure your Delphix Engine is powered on
INFO:2015-09-10 15:45:48:Scanning for the Landshark Delphix Engine
INFO:2015-09-10 15:46:04:Did not finr a suitable Landshark Delphix Engine.
Repeating discovery loop in 60 seconds.
Ensure your Delphix Engine is powered on
INFO:2015-09-10 15:47:04:Scanning for the Landshark Delphix Engine
INFO:2015-09-10 15:47:13:Did not finr a suitable Landshark Delphix Engine.
Repeating discovery loop in 60 seconds.
Ensure your Delphix Engine is powered on
INFO:2015-09-10 15:48:13:Scanning for the Landshark Delphix Engine

Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
The Linux Target can't see the DelphixEngine. What is the IP address of the linuxtarget and the DelphixEngine? You should be able to see this on the console.
Photo of saran

saran

  • 140 Points 100 badge 2x thumb

Linux Target 10.0.2.4

Delphix Engine 10.0.2.5

Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
So you are using Landshark 2.2 and DelphixExpress?
Photo of saran

saran

  • 140 Points 100 badge 2x thumb

Yes Landshark 2.2 and DelphixExpress 4.3.1.0

Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
Ok. As the delphix user on the linuxtarget, what is the output of 

grep "Network" /home/delphix/landshark_setup.log
Photo of saran

saran

  • 140 Points 100 badge 2x thumb
DEBUG:2015-09-10 14:48:32:Landshark Linux Target Network info is 192.168.56.101/24
DEBUG:2015-09-10 15:33:22:Landshark Linux Target Network info is 192.168.56.101/24
DEBUG:2015-09-10 15:43:21:Landshark Linux Target Network info is 192.168.56.101/24
Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
Ok, That is good. Are you following these instructions? 
Quick Start for Landshark on VirtualBox
(Edited)
Photo of saran

saran

  • 140 Points 100 badge 2x thumb

Yes, I have followed the same steps and did not find the expected result in log file as per 11th step.

 

Photo of Adam Bowen

Adam Bowen, Official Rep

  • 17,418 Points 10k badge 2x thumb
Saran, I mistakenly posted the wrong link in the comments (I have since edited it). You are using the old documentation.

Please see Quick Start for Landshark on VirtualBox to get your networking configured.